Hear From Our Clients
You’ve got water stains spreading across your ceiling. Maybe you’re seeing white powder on the bricks outside, or your damper’s rusting out. That’s not cosmetic—that’s your chimney failing, and it’s only going to get worse.
Here’s what happens when you fix it right: no more water pooling in your attic during storms. No more worrying about carbon monoxide backing up into your home. Your heating system works the way it should, your energy bills stop creeping up, and you’re not calling someone back out in two years because the repair didn’t hold.
Most chimney repairs in Miller Place run between $1,200 and $2,500 depending on what’s actually broken. That sounds like a lot until you compare it to the $10,000+ you’ll spend if water gets into your walls or foundation. Fixing it early isn’t just smart—it’s the only move that makes financial sense.
Home Team Construction has been fixing chimneys across Long Island for over a decade. We’re not a franchise or a call center—we’re local contractors who understand what salt air and freeze-thaw cycles do to masonry.
Every job we take on reflects directly on our reputation in this community. That means we don’t cut corners, we don’t upsell you on work you don’t need, and we don’t disappear after cashing your check. You get licensed, insured professionals who’ve seen every type of chimney problem Miller Place throws at us.
We’ve repaired chimneys that were leaking for years, rebuilt crowns that crumbled after one bad winter, and stopped flashing failures before they turned into interior damage. You’re hiring people who know exactly what they’re looking at when they climb on your roof.
First, we come out and actually look at your chimney—not just from the ground, but up close where the damage is happening. You get a same-day assessment that tells you what’s broken, why it’s broken, and what it’ll cost to fix it. No vague estimates, no “we’ll know more once we start” nonsense.
Once you approve the work, we schedule around your life, not ours. We show up when we say we will, protect your property with tarps and coverings, and get to work. If it’s a flashing issue, we’re pulling back shingles and installing new metal that’s sealed properly. If it’s masonry damage, we’re repointing mortar or replacing bricks with materials designed for coastal conditions.
When we’re done, you get a walkthrough showing exactly what we fixed and why it matters. We clean up completely—no nails in your driveway, no debris in your yard. And if something doesn’t look right to you, we address it before we leave. The work comes with a warranty because we stand behind what we do.
Ready to get started?
Chimney flashing repair means we’re replacing the metal seals where your chimney meets your roof—the most common leak point on Long Island homes. We use materials rated for coastal exposure, not the cheap aluminum that corrodes in three years.
Masonry work covers cracked bricks, deteriorating mortar joints, and damaged chimney crowns. Miller Place homes deal with accelerated wear because moisture gets into those cracks, freezes, and expands by about nine percent. That pressure destroys masonry faster than almost anything else. We repoint with mortar that’s mixed correctly for the existing brick, and we rebuild crowns with proper slope and overhang so water runs off instead of soaking in.
If your chimney’s leaking, we’re also checking the cap, the liner, and the interior for hidden damage. Water doesn’t just stay in one place—it travels. We find where it’s going and stop it at every point. You’re not paying for a patch job that fails next winter. You’re getting a repair that lasts fifteen to twenty-five years when it’s done with the right materials and actual skill.
Most homeowners in Miller Place spend between $1,200 and $2,500 for typical chimney repairs. That range covers common issues like flashing replacement, repointing mortar joints, or fixing a damaged crown.
Basic repointing work—where we’re filling in deteriorated mortar between bricks—runs about $350 to $1,200 depending on how much of the chimney needs attention. If you’ve got bricks that are cracked or falling apart, brick replacement costs between $900 and $4,000 based on how extensive the damage is. Full chimney rebuilds are rare but can run significantly higher if the structure’s compromised.
The real cost comes from waiting. A small leak you ignore today turns into water damage in your attic, stains on your ceiling, and eventually structural problems that can hit five figures. Fixing it early is always cheaper than fixing it late.
Cleaning removes creosote buildup and debris from inside your chimney. Repair fixes structural damage that’s letting water in or creating safety hazards. They’re completely different problems.
You need repair if you’re seeing water stains on the ceiling near your chimney, white staining on the exterior bricks, rust on your damper, or pieces of mortar in your fireplace. Those are signs that water’s getting in or your masonry’s failing. You might also notice smoke backing up into your house, which means your flue’s blocked or damaged.
Cleaning is maintenance you do annually to prevent creosote fires. Repair is what you do when something’s actually broken. If you’re not sure which one you need, we’ll tell you during the inspection—and we’re not going to sell you repair work if all you need is a sweep.
Salt air and freeze-thaw cycles destroy masonry faster on Long Island than almost anywhere else. You’re dealing with moisture from coastal weather that gets into tiny cracks in your bricks and mortar.
When temperatures drop below freezing—which happens plenty during Miller Place winters—that moisture freezes and expands. Ice takes up about nine percent more space than water, and that expansion puts massive pressure on your masonry. Over time, it cracks bricks, pushes mortar out of joints, and breaks down your chimney crown.
Add in salt air that corrodes metal flashing and accelerates deterioration, and you’ve got chimneys aging twice as fast as they would inland. That’s why using coastal-rated materials matters here. Standard flashing and mortar mixes don’t hold up. You need repairs designed specifically for what Miller Place weather does to chimneys.
A properly done chimney repair with the right materials should last fifteen to twenty-five years in Miller Place. That assumes you’re using flashing and mortar rated for coastal conditions and the work’s done correctly the first time.
Cheap repairs with wrong materials fail in three to five years. We see it constantly—someone hires the lowest bidder, they use standard aluminum flashing or improper mortar mix, and it’s leaking again before the homeowner even realizes there’s a problem. Then they’re paying twice: once for the bad repair and again for the one that actually works.
The longevity also depends on maintenance. Annual inspections catch small issues before they become expensive ones. If you’re checking your chimney every spring after winter weather does its damage, you can address minor problems for a few hundred dollars instead of waiting until you need major work.
Repointing means we’re removing deteriorated mortar from the joints between bricks and filling them with new mortar. The bricks themselves are still solid—it’s just the mortar holding them together that’s failed. This runs about $350 to $1,200 depending on how much of the chimney needs work.
Brick replacement is what happens when the bricks themselves are cracked, crumbling, or damaged beyond repair. We remove the bad bricks and install new ones that match your existing chimney. This costs more—usually $900 to $4,000—because it’s more labor-intensive and requires matching brick types.
Most Miller Place chimneys need repointing before they need brick replacement. Mortar’s softer than brick, so it deteriorates first. That’s actually by design—it’s easier and cheaper to replace mortar than bricks. But if you ignore failing mortar long enough, water gets behind the bricks and damages them too. That’s when a $600 repointing job turns into a $3,000 brick replacement.
You can technically do some chimney work yourself, but most homeowners shouldn’t. Chimney repair requires working on your roof, understanding masonry techniques, knowing building codes, and having the right tools and materials. Most importantly, it requires knowing what you’re looking at when you assess damage.
The biggest risk isn’t just doing the work wrong—it’s misdiagnosing the problem. You might see a small leak and think it’s just flashing, but the real issue is a cracked crown or damaged liner. You fix the flashing yourself, the leak continues, and now you’ve wasted time and money while water’s still destroying your home.
We carry liability insurance, know local building codes, and have done this work hundreds of times. We catch problems you wouldn’t notice and fix them with materials that actually last in coastal conditions. The cost of hiring someone who knows what they’re doing is almost always less than the cost of fixing a DIY job that failed—plus whatever additional damage happened while you were figuring it out.
Local Resources
Useful Links
Other Services we provide in Miller Place
